<![CDATA[Audio buzzer.]]>Hi.

I purchased T-Beam SoftRF SX1262 / 868MHz IPEX. My question: what pins should I connect the audio buzzer to (in the version with two outputs and in the version with three outputs)?

Thanks for the answers.

]]>https://www.community.lilygo.cc/topic/1050/audio-buzzerRSS for NodeSat, 16 May 2026 12:05:35 GMTSun, 30 Jun 2024 09:22:19 GMT60<![CDATA[Reply to Audio buzzer. on Mon, 01 Jul 2024 13:50:28 GMT]]>@teastain2 All right. I'll try. I was hoping that maybe someone here had already encountered this problem and could help me.
Thank you.

]]>https://www.community.lilygo.cc/post/1899https://www.community.lilygo.cc/post/1899Mon, 01 Jul 2024 13:50:28 GMT<![CDATA[Reply to Audio buzzer. on Sun, 30 Jun 2024 21:35:04 GMT]]>@uid0 This forum is for all LilyGO products and Arduino IDE examples.
Lora, Meshtastic and Glider firmware is in the realm of the firmware developer.
The image I posted says that buzzer is not available for Prime Mark II.
Here is the developer GitHub repository:
https://github.com/lyusupov/SoftRF/wiki/Prime-Edition-MkII
You can raise an Issue there:
https://github.com/lyusupov/SoftRF/issues

-Good luck!
-Terry

]]>https://www.community.lilygo.cc/post/1897https://www.community.lilygo.cc/post/1897Sun, 30 Jun 2024 21:35:04 GMT<![CDATA[Reply to Audio buzzer. on Sun, 30 Jun 2024 19:58:35 GMT]]>@teastain2 said in Audio buzzer.:

If you cannot edit the program, then you must find out from the software author what pins to use.

Thank U for the RE.

I just have no idea how to contact him. I thought someone from this forum had encountered this problem and could help me.

]]>https://www.community.lilygo.cc/post/1896https://www.community.lilygo.cc/post/1896Sun, 30 Jun 2024 19:58:35 GMT<![CDATA[Reply to Audio buzzer. on Sun, 30 Jun 2024 18:52:05 GMT]]>@uid0 So, the image that you posted is from what software?
If you cannot edit the program, then you must find out from the software author what pins to use.
Screenshot 2024-06-30 at 2.51.35 PM.png

]]>https://www.community.lilygo.cc/post/1895https://www.community.lilygo.cc/post/1895Sun, 30 Jun 2024 18:52:05 GMT<![CDATA[Reply to Audio buzzer. on Sun, 30 Jun 2024 17:06:38 GMT]]>@teastain2 said in Audio buzzer.:

Hi! How will you program this buzzer? There are many pins available.

I use SoftRF software. I use Prime Mark II. By default, there is no: Barometric sensor (but I installed it - it works). By default there is no: Audio buzze - I would like to add. I believe this is possible (since I added BMP280). Now I use PIN (they are occupied): 3V3, GND, 22, 21 (for LCD and BMP280). Thanks for the answers.

control for volume level of Standalone Edition's built-in speaker

]]>https://www.community.lilygo.cc/post/1894https://www.community.lilygo.cc/post/1894Sun, 30 Jun 2024 17:06:38 GMT<![CDATA[Reply to Audio buzzer. on Sun, 30 Jun 2024 16:04:22 GMT]]>@uid0 said in Audio buzzer.:

T-Beam SoftRF SX1262 / 868MHz IPEX

Hi! How will you program this buzzer? There are many pins available.
-Terry

]]>https://www.community.lilygo.cc/post/1893https://www.community.lilygo.cc/post/1893Sun, 30 Jun 2024 16:04:22 GMT